Plans ideas

Unplugged Summer Part Three

Building a Stand for the Dovetailed Box













With the dovetails dry fit Ill take some of my scrap wood and try to get a sense of the weight and dimension the stand should be for the piece. I want things to be slight and skinny, with a modern sensibility about it. The exposed joinery on the box will also be reflected through the stand joinery but first Ill have to dimension some stock.
















This 16 long plank of Khaya would be a dream to most but sadly its so warped and twisted that getting a 30" length out of it without any kind of hollow or wind proves to be a real challenge. (now whats that about building myself that new 16 work bench?)

















Ill continue on with some cross cutting and ripping followed by some more surfacing, shooting and then smoothing until I have all of the components needed to make up the stand.

















The Tite-Mark is again in high demand around the wood shop and the stock thicknessing is a slow but pleasant affair. Ill scribe one side of the long narrow leg and then over to the bench for another round of surfacing...
The process is repeated again at my make shift saw bench.






















Above you can see the nice deep scribe line Ill be able to cleanly plane to; the round blade and body of this style marking gauge makes it easy and accurate to roll around the edges of the work piece.






















With the legs silky smooth Ill go ahead and glue together the box. Once dry I can finish plane it and then start fitting the legs to snugly wrap around the dovetailed carcass. Ill lay things out on the bench with clamps and knife in the joinery lines.
















The top corners of the frame will be simple bridle joints with some mortise and tenon joinery for the cross stretchers and feet. This is a good half day of work getting the lower frame dimensioned with the joinery laid out. Ill leave it there for today and start sawing the corner joints and chopping the mortises in the morning...














5 a.m. and Im up to get the early worm. Some coffee and a fire will clear away yesterdays shavings and Ill begin the joinery. In the next shot you can see Ive laid out the mortises but I totally gapped on any shots of the bridle joint sawing.

















The pieces are clamped securely down to the bench to with my surface clamp and a scrap oard so I dont bruise the freshly planed surfaces. Ill carefully chop out the waste with my mortise chisel and go ahead sawing the tenons. This process continues on from mortise to tenon, bridle to bridle.














I find some days that these early morning wake up calls can get the brain on auto-pilot and before I know it Im dry fitting the front lower assembly.
I say front assembly because Ive decided to make two upright frame sections for the stand; a thinner front assembly with an identical rear frame slightly larger than the first. This will add to the modern effect Im looking for, almost cosmopolitan or a reflection of the city scape Ive left behind a few weeks ago.






















The shot above shows the front assembly clamped into my shoulder vise with the rear assembly piece balanced to see if I like where Im going. Again the design evolves as I work and I allow the wood to dictate the forms as they develop into this small frame assembly almost alien in nature holding up the small structure.






















The rear frame components follow the same pattern as the first only with slightly larger pieces and joinery. Im moving along and am excited to get the feet started so I can stop rigging things up with clamps on the bench top. In the last shot you can see some of my Cabinet Master clamps acting as feet to hold the work tall and proud, this will again assist me in delivering a verdict on this design.






















Im happy with the way this piece is progressing and Ill rough out some stock for the feet. I decided to add another lower cross stretcher giving some more stability when the carcass gets pushed a little further through the frame opening and cantilevers out a little bit more. The front left leg has a wild twist in it; I didnt notice it until the four legs are together around the carcass. I think about removing it but later choose to let it stay where it is. It gives the piece a strange kind of movement, almost a sense of waiting, perhaps on a journey somewhere?
Ive got the feet to chop for the leg tenons and then I can do some more shaping. This will have to wait a few days; we have some summer company coming to visit and theres a list as long as my arm of things needing to be done around the house. Im off to the timber frame pile next to the shop to cross cut some planks for my daughters bed. We just set up a nice old sleigh bed for her and it seems to be missing the cross rail supports thatll lie underneath the mattress. So with my panel saw and a framing square I have about 32 cross cuts to make in some old planks. It feels good for the soul to be outside under this summer sun working wood again.














Stay tuned...